toolguy (90)
Straight type, no markings but about .560", still has an edge. More tools when you click on toolguy.
Glass cutters, Red Devil, multi-wheel made in England, one is made in Germany all 5 for $10. More tools when you click on toolguy.
1 1/2" Pipe tap. More tools when you click on toolguy.
1/4" Hex bits metric 6-12mm, fraction 3/16"-1/2". More deals when you click on toolguy.
About 115, including Torx, Robertson, Phillips, slots, nut drivers, wood drills, bit holder. More tools when you click on toolguy.
3 Lighted 12 volt testers, anti-freeze, coolant tester, tire filler, tire gauge, new metric drain plug with magnet, 2 Fire Fly lighted valve stems, 2...
Heavy duty well made for commercial use, 2 different punches, triangular shape and 1/8" holes, one is a railway punch, your choice $10 each. More dea...
3/8" Drive metric sockets 8-19mm, FRACTIONAL 3/8"-13/16", and a deep set 1/4"-13/16", with u-joint socket, extension, ratchet, some srcrewdrivers, ...
30 Piece set with case Torx, Robertson's, Phillips, slots and socket adapter, magnetic tip for hex bits
More tools when you click on toolguy.
Each door is 36 1/2" wide and 81" tall, have the rail but probably not the hardware to mount it and one roller bis missing, bypass type, hardware ki...
5 Machine screw sizes and 1/4"- 1/2" N.C & N.F, the 1/4" has the taper, plug, bottom taps, many are made in USA, Canada or England, also includes ...
Norton USA,1/4" x 7", engineered for aluminum, free cutting non loading, pair $5. More deals when you click on toolguy.
Made of plywood and reinforced inside corners, includes foam dividers, outside dimensions 9 3/4" x 19 3/4" x 12" high, could be used for storage or ...
HSS For drilling steel, Brad point for wood, carbide tipped for concrete, plastic case is cheap but the drills are good, 10 pieces $10. More deals wh...
New Mastercraft takes standard T50 staples, a few included, firm price. More tools when you click on toolguy.
Pre Press mould 2" x 4", nice chunk of aluminum for a milling project, new cost for this is about $40. More deals when you click on toolguy.
One hole paper or gasket punch, very well made by Wilson Jones No.110, cast base with spring return, also includes a standard type also made in USA, ...
NICO PRESS No.17-2 & No.17-BA, Small hole is just under 1/16", other hole is just over 5/64", for crimping small steel wire using oval sleeves but may...
Copper piece is about 9 1/2" x 9 1/2", made of 3/4" copper rings, triangle piece is about 12" x 12" with 7/8" aluminum rings, all hand made, $15 ea...
Ungar 27 watts, new wedge shaped tip. More tools when you click on toolguy.
Came off an older Craftsman, center of 1/4" rods are about 4 7/8" center to center. More deals when you click on toolguy.
Pockets on the chest and legs, your legs fit through a cuff on the back to keep the apron in place. More deals when you click on toolguy.
1/2" BX or armoured cable connectors, also good for loomex, these are a standard & most common size, all come with lock nuts, a couple of different st...
Made by C-L USA, 27/64" and 17/32", new condition, pair $25 or bundle with the other set listed for a total of $120. More deals when you click on too...
Cal Pump Model A430, up to 430 gallons per hour, motor runs in oil bath, operates in any position, corrosion resistant, new cost well over $100. Mo...
toolguy
Gerard Volk
Victoria
Tools